Object Terminal “Antaeus” AS006G and AS006GD “Voron”

Being a part of transmitting system “Antaeus” this equipment is designed for central guard of domestic/industrial premises and prevention of infiltration and fire. This goal is achieved by monitoring of system loops with installed alarm/fire annunciators and by sending alarm messages to the central surveillance console or to the user’s mobile telephone. Messages are sent on the telephone (by setting dial-up connection) or through the GSM-net (in case of line damage). If necessary you can se one of the two mode of transmissions. There are three data formats for sending messages to the CSC, the usual ADEMCO ID Contact, ADEMCO Express or the new “Presto” format, characterized by higher reliability, speed and mimic resistance. Mobile messages are sent as SMS.

The OT may be engaged/disengaged with the help of remote controls coming with the equipment. Besides these remotes can make an emergency call. It can also be done with the help of side-mounted keyboard, connected to OT. Other peripheral units can also be connected to OT, such as remote sense light, alerter etc.

In case of intrusion into the guarded object press the help button. Otherwise the fire suppressing gauge of the OT will send a telephone or radio message to the CSC, installed at the company providing service of the object. On receiving the message the service company identifies the address, the type of intrusion with other identification signs and takes measures targeted at property protection and criminal apprehension.

The handling is performed with the help of side-mounted keyboard ADEMCO 6128. Also you can connect two remote indicators showing the current status of OT. It may be single light-emitting diode or light annunciator with voltage 12V (e.g. annunciator “Mayak”).

OT may send alarm/service messages through two telephone lines and as SMS.

OT may control SMSs from the user’s cell phone. You can send certain messages in order to engage/disengage the security system or check the quality of communication with the CSC. For reasons of safety each SMS should have identification number and a password. This option may be switched off.

There are two modifications of the OT – AS006G and AS006GD. AS006G is used with remote controls and AS006GD is used with electronic keys iButton.

OT makes it possible using up to 9 remote controls/electronic keys iButton with unique codes as well as identification of each (there may be more, but in this case part of them must have similar codes). Each remote has two buttons: “Guard” (“1”, engaging/disengaging) and “Panic” (“2”) for making emergency call (one of these functions may be switched off if necessary). Electronic keys iButton may be uses for engaging/disengaging of the security system only, still they are characterized by much more cryptographic security.

OT supports programmable delay (0…198s) at the input/output.

OT supports GSM net within 900/1800 mHz, Phase 2+, class 4 (900 mHz, 2W) and class 1 (1800 mHz, 1W) and interfacing with the telephone line according to Russian State Standard GOST 25007-81. Both pulse and tone dialing are possible.

OT supports three FTP:

·        ADEMCO ID Contact;

·        ADEMCO Express;

·        “Presto”.

FTP for each routing is set individually.

The OT may automatically monitor the fund balance of the cellular service provider notifying the CSC and sending SMSs to the cell user. User can also check his/her balance at any moment.

OT enforces provides up to six alarm system loops. The source voltage for three main loops is 12V. OT registers closed, normal and open conditions of the loops with “normal”, “fast” and “special” modes. Protect mode registers 5 conditions, that is normal, one sensor functioning, two and more sensors functioning, loop closure and loop break. OT allows connecting loop-powered sensors, with source voltage 12V and total input current 0.6 mA in customary mode and 1.5 mA in “special” mode. It is also possible to install sensors with external power supply – OT itself, for example, provided that current-carrying rating (0.8 mA for all peripheral units) is observed.

The mode for each zone is programmed individually.

The main loops’ characteristics are given n the table:

OT may monitor the working order of loops and battery, the integrity of operation information, the condition of GSM-modem and registration in GSM network. At the same time OT allows guarding of objects in the presence of loops’ defects.

As a part of OT you acquire an event-programmed relay for connecting peripheral units (light/sound annunciator). Hump current is 2A, maximal voltage – 400 V.

OT supports keeping and viewing of event log (32 events)

OT supports keeping up to nine user passwords, forcing password and administrator’s password preventing illegal interference.

OT may periodically send status messages to CSC. The interval of message sending may be 2-18 hours.

OT also offers on-line diagnostics of loops and connection with CSC.

It also makes possible connecting of auxiliary equipment such as light/sound indicators with voltage 12V. The total current must not exceed 0.8 A.

OT is powered through the AC network (220 V, +22-33; 50±1Hz). The wattage must not exceed 20 W. OT has got a backup supply source that is battery FIAM-GS with capacity 4.5 ampere-hour. The switching to the backup supply source and charging at presence of the primary power supply are automatic. With fully charged battery OT operates during 24 hours (without auxiliary equipment). In case of battery running out OT sends message to CSC.

The temperature of the premises where OT is set should be +1-+40 C, with relative humidity up to 90% at temperature 25C (hardness group 4 according to Russian State Standard (GOST) 15150?69).

OT provides electromagnetic compatibility according to hardness group 3, GOST 50009092.

OT size should not exceed 200x210x60mm, weight is 3.5 kg at most.

Configuration of “Antaeus” AS006G and AS006GD “Voron”:

Object terminal “Antaeus” AS006G and AS006GD – 1

Light-emitting diode ÀË307Á ÀÀ0.336.076ÒÓ – 1

Antenna ADA-0062 – 1

Resistor Ñ2-33-0.25 2.2kOhm ÎÆ0.467.173ÒÓ  – 7

Remote control (for AS006G) only – 2

Contactor DS9092 (for AS006GD only) – 1

Electronic key DS1990 (for AS006DG only) – 2

Operation manual – 1

Package – 1 set